- +971 4 578 7532
- +971 50 803 1253
- sales@deltapower.ae
Metal Seated
The bonnet type Gate Valves have a revolving non-rising stem, provided with a functional thread which is inside the valve chamber.
During the operation, stem revolves in the stem nut which carries along a flexible wedge. Due to its design, low torque values are achieved which eases the revolving of the stem.
The stem is locked against axial movement by a bonnet nut threaded to the bonnet, and no axial movement occurs in the specified conditions.
The wedge is guided in the body in a precast groove and provides an undisturbed water flow when the valve is open.
The body and the wedge have pressed-in/ threaded sealing seat to have drip tight sealing when the valve is closed.
Multi Core and Heat Resistance Cables
Application: Used in locations where high resistance to heat, oil and fire (HOFR) are required. Commonly used in lifts, cranes, pumps and other heavy duty equipment.
Types and Sizes: Single & multi core from 0.5 sq.mm to 630 sq. mm
Conductor: Flexible Tinned Copper Conductor
Insulation: EPR, CSP, PCP, Silicone Rubber
Inner Sheath: EPR, CSP, PCP, Silicon Rubber
Armour: Copper Wire / Stainless Steel Braiding
Outer Sheath: EPR, CSP, PCP, Silicone Rubbe
Needle Plunger Valve
Needle Valves open and close by the axial movement of the disc that is connected to a crank and shaft mechanism which the gearbox commands.
When the valve is in fully open position, due to its aerodynamic design, it causes very low head loss and maximum flow capacity.
The disc is guided by circular disc guides deposit welded to the main body, which causes minimum friction loss and stable movement.
Stem, rotated by the gearbox, commands the crank mechanism which moves the disc axially to change the opening area of the valve.
When the valve is in fully closed position, due to special sealing mechanism, drip tight sealing is achieved.
Due to pressure-independent disc operation and special gearbox, torque values needed even in large sizes are minimum.
Nut Bolts and Washer
Fasteners: We supply variety of standard and special-grade fasteners a broad range of extremely reliable, precise and accurate Stud Bolts, Anchor Bolts, U Bolts, Threaded Bars in Steel and Steel Alloys of different sizes from high-quality grade raw material. At the same time we can facilitate customers by our ready stock, for hex nuts, heavy hex nuts, jam nuts and washers in black, electro galv., hot dip galv., stainless steel finish.
Pipe Repair Clamp
A clamp for quick repair of pit holes, punctures or splits in steel pipe. Repairs leaks on water, gas, oil and pressure steam lines up to normal working pressure 10 Kgf/cm². Suitable for repairs of steel, cast iron, brass, asbestos cementos and plastic pipes.
Plastic Cell Soak away System
Local rainwater infiltration is often required by law. As more and more ground is sealed with buildings, car parks and roads, the sewer system is having to work harder and the risk of flooding increases. Our infiltration systems are here to help. They make sense both ecologically and economically because they take the strain off the sewer network and save surface water drainage charges.
Plastic storage systems have become a popular solution for rainwater infiltration and retention. Infiltration ditch bodies require very small amounts of space compared with gravel ditches or drainage pipes. They offer a large infiltration volume for a low weight. Other benefits of infiltration modules include their high load capacity and durability.
Plug Valve
Critically acclaimed for raw sewage lines, for shut off service. Eccentricity of the plug (and its turning away from the flow path) is a great feature in allowing (sewerage) solids to pass freely. Sizes and Pressures. Sizes 3” (DN80) to 48” (DN1200) and Pressures of PN10, PN16. Smaller sizes up to DN300 can also be rated PN25
PLUG VALVES
Critically acclaimed for raw sewage lines, for shut off service. Eccentricity of the plug (and its turning away from the flow path) is a great feature in allowing (sewerage) solids to pass freely. Sizes and Pressures. Sizes 3” (DN80) to 48” (DN1200) and Pressures of PN10, PN16. Smaller sizes up to DN300 can also be rated PN25
Polythene Sheets
Polythene sheets are used during building construction to prevent structural damping that occurs when warm, moist air penetrates inside a concrete slab, wall, roof or floor structure reaches the dew point, and then condenses into liquid water.The warm, damp air may penetrate a wall from the inside of a heated building in a cold climate or from the exterior of an air-conditioned building in a warm climate..
This condensation may allow mold growth, rotting of timber, corrosion of metal components and reduction in the thermal insulation’s effectiveness.
The resulting structural damage may occur without visible indications until significant damage has occurred.
The most effective method of controlling damping is using an impervious vapor-barrier on the warm side of the structure.
It has an extremely low water permeability rating of typically 1.7SI Perms.
It can be used in between the insulation material and structure surface to act as a damp-proof membrane.
On site concrete slabs employ a 1000 guage (250 microns) polythene sheet laid underneath the concrete to prevent the moisture from being absorbed.